VIP Adventurer
RC Car & Transmitter
1 - 24 of 54 products
-
Best seller Save $50.00
-
Best seller Save $60.00
-
Save $20.00
-
Save $30.00
-
US only Save $50.00
-
US only Save $70.00
-
US only Save $40.00
FMS 1:24 FCX24 Chevrolet K5 BLAZER PRO RTR 18th Anniversary Brushless Edition Sold out$159.99 USD $199.99 USD -
Save $20.00
-
US only Save $50.00
-
Save $60.00
EAZYRC 1:18 Chevrolet Colorado Off-Road Truck RTR Brushless Version In stock$89.99 USD $149.99 USD$89.99 USD -
-
FMS 1:24 FCX24 Chevrolet K5 Blazer RTR
Description
| Length | 253mm |
| Width | 129mm |
| Height | 128mm |
| Wheelbase | 139mm |
| Tire F/R | Φ 54.8*19.5mm |
| Approach Angle | 57° |
| Departure Angle | 45° |
| Ground Clearance | 38mm |
| Motor | 130 Brushed Motor |
| Remote control distance | 30m |
| Approx. operating duration time | 20mins |
FMS 1:18 FCX18 LC80 Toyota Land Cruiser 80 RTR
Description
|
Product |
Model FS-MG41-BS |
|
RF |
2.4GHz ISM |
|
|
<20dBm (e.i.r.p.) (EU) |
|
2.4GHz Protocol |
2A-BS |
|
Resolution |
1024 |
|
Input Power |
6V/DC or 1.5AAA*4 |
|
Low Voltage Warning |
<4.2V |
|
Dimensions |
118*73*145mm |
FMS 1:24 FCX24M Land Rover Camel Trophy Edition RTR
Description
| Model | Discovery | Range Rover | Defender 110 | Defender 90 |
| Length | 232mm | 227mm | 240mm | 214mm |
| Width | 105mm | 103mm | 107mm | 107mm |
| Height | 133mm | 120mm | 128mm | 128mm |
| Wheelbase | 134mm | 134mm | 135mm | 111mm |
| Tire F/R | Φ 48*17mm | Φ 48*17mm | Φ 50*20mm | Φ 50*20mm |
| Approach Angle | 52° | 64° | 55° | 55° |
| Departure Angle | 55° | 47° | 49° | 51° |
| Minimum Ground Clearance |
28mm | 28mm | 29mm | 24mm |
| Motor | 050 Motor Set | |||
| Battery | 7.4v 380mAh | |||
FMS 1:24 FCX24 Power Wagon RTR
Description
The World's First 1/24 Climbing Rock Crawler with Two-speed Transmission - Power Wagon FCX24
FCX24 meticulously designed by FMS team will redefine the small scale climbing rc car. As the first product of the FCX24 series, the car body is the POWER WAGON in 1949, which appeared in the form of a mud off-road truck. It is positioned as a high-performance crawler chassis. The carframe is made of high-strength nylon. Compared with the trapezoidal beam spliced by metal side beams and plastic trusses, the overall weight is lighter and the strength is higher. The mid-mounted power assembly has a low center of gravity and integrates the 2-speed transmission, transfer case and 130 motor. The power is transmitted to the front and rear axles through the universal joint drive shaft. The axles are equipped with wheel side reducers, commonly known as "portal axle", which can increase the ground clearance of the differential tooth pack and improve the passability.
What's in Box:
- 1 x 1:24 Power Wagon RTR
- 1 x G3 V1 Transmitter
- 1 x R3A V1 Receiver (installed)
- 1 x 130 Brushed Motor (installed)
- 1 x 7.4V 380mAh Battery
- 1 x USB Battery Charger
- 1 x Hex Wrench Socket
- 1 x Product Manual
Need to Complete:
- 4 x AAA Batteries for Transmitter
FMS 1:18 FCX18 Chevrolet K10 RTR
Description
|
Product |
Model FS-MG41-BS |
|
RF |
2.4GHz ISM |
|
|
<20dBm (e.i.r.p.) (EU) |
|
2.4GHz Protocol |
2A-BS |
|
Resolution |
1024 |
|
Input Power |
6V/DC or 1.5AAA*4 |
|
Low Voltage Warning |
<4.2V |
|
Dimensions |
118*73*145mm |
FMS 1:24 FMT24 Chevrolet Colorado Monster Truck RTR
Description
| Length | 239mm |
| Width | 161mm |
| Height | 108mm |
| Wheelbase | 140mm |
| Tire F/R | D: 64.8mm, W: 33.4mm |
| Minimum Ground Clearance | 37mm |
| Approach Angle | 66° |
| Departure Angle | 53 ° |
| Motor | 370 brushed motor |
| Servo | 13g metal servo x 1, 9g servo x 1 |
| Battery | 2S Lipo 7.4V 900mAh 25C |
| Remote Control Distance | 80m |
| Approx. Operating Duration Time | 20mins |
| Remote Control | G3 V3+ R3B transmitter, receiver with ESC group control board |
FMS 1:10 FCX10 Chevrolet K5 Blazer RS
Description
| Length | 548mm |
| Width | 249mm |
| Height | 285mm |
| Wheelbase | 324mm |
| Tire F/R | Φ 46*120mm |
| Approach Angle | 58° |
| Departure Angle | 48° |
| Ground Clearance | 89mm |
| Motor | 550 Brushed Motor |
| Remote control distance | 150m |
| Remote control | 2.4GHz 11CH Remote Control System |
| Recommended Battery | 2S Lipo 7.4V 2000mAh XT60 plug x1 (Product does not include batteries.) |
| Battery Compartment | 140 x 47 x 30mm |
FMS 1:10 FCX10 LC80 Toyota Land Cruiser 80 RS
Description
| Length | 572mm |
| Width | 251mm |
| Height | 288mm |
| Wheelbase | 325mm |
| Tire F/R | Φ 46*120mm |
| Approach Angle | 51° |
| Departure Angle | 42° |
| Ground Clearance | 76mm |
| Motor | 550 32T Brushed Motor |
| Remote control distance | 150m |
| Remote control | 2.4GHz 6CH Remote Control System |
| Recommended Battery | 2S or 3S 5000mAh XT60 plug x1 (Product does not include batteries.) |
| Battery Compartment | 140 x 47 x 40mm |
ROCHOBBY 1:10 Atlas 4x4 Off-Road Truck RS
Description
ROCHOBBY 1:10 Atlas 4x4 Off-Road Truck RS
This 1:10 Atlas 4x4 is designed in the form of an off-road truck racer. The car body is moulded with PC plastic, which is light in weight and has a low center of gravity; the nylon roll cage at the back can protect the car shell during rollovers. The rigid metal frame and four-link suspension system ensure strong climbing ability. The chassis has proven reliability. In both dynamic and static aspects, the real vehicle has been painstakingly restored.
What's in Box:
- 1 x 1:10 1:10 Atlas 4x4 RS
- 1 x 2.4GHz Transmitter
- 1 x 2-in-1 Receiver / 40A ESC (installed)
- 1 x 550 Brushed Motor (installed)
- 1 x 9g Plastic Digital Servo (installed)
- 1 x 15kg Metal Digital Servo(installed)
- 1 x Product Manual
Need to Complete:
- 4 x AA Batteries for Transmitter
- Battery for Kit (Recommended 2S LIPO 5000mAh XT60 plug)
Specification:
- Length: 537mm
- Width: 241mm
- Height: 247mm
- Wheelbase: 340mm
- Tire F/R: Φ 120mm
- Approach Angle: 63°
- Departure Angle:53°
- Ground Clearance: 79mm
- Motor: 35T 550 Brushed motor
- Driving speed: up to 15km/h
- Remote control distance: 80m
- Approx. operating duration time: 20mins
- Remote control: 2.4GHz Transmitter (Fibre Style) & Receiver Set
FMS 1:10 Toyota Land Cruiser FJ40 RS
Description
| Length | 571mm |
| Width | 268mm |
| Height | 326mm |
| Wheelbase | 339mm |
| Tire F/R | Φ 115mm |
| Approach Angle | 65° |
| Departure Angle | 40° |
| Ground Clearance | 82mm |
| Motor | 35T 550 Brushed motor |
| Remote control distance | 80m |
| Remote control | 2.4GHz Transmitter (Fibre Style) & Receiver Set |
FMS 1:12 Land Rover Series II RTR
Description
Adventurer's Staple, Off-Road Legends - 1:12 Land Rover
The Land Rover Series 2 is an iconic off-road vehicle that well represents the adventurous spirit of the Land Rover brand. It combines outstanding durability with outstanding versatility, making it the ideal companion for outdoor enthusiasts and adventure seekers.
The new Land Rover Series II launched by FMS inherits the essence of real cars in terms of highly realistic appearance, comfortable fully simulated interior, durable chassis and powerful power system.
Whether traversing rugged mountains, traversing muddy trails, or crossing rivers, FMS-Land Rover Series 2 can bring an exciting and reliable handling experience, embodying the spirit of pioneering adventure, allowing players to create unforgettable memories.
What's in the box:
- 1 x 1:12 Land Rover Series II RTR
- 1 x 2.4G Transmitter + 2 in1 ESC & Receiver (installed)
- 1 x 180 Brushed Motor (installed)
- 3 x 3Y 9g Digital Servo (installed)
- 1 x 2S Lipo 7.4V 380mAh Battery
- 1 x USB Battery Charger
- 1 x Hex Wrench Socket
- 1 x Product Manual
- 1 x Bind Connector
Need to Complete:
4 x AAA Batteries for Transmitter
Specification:
- Length: 270mm
- Width: 135mm
- Height: 149mm
- Wheelbase: 169mm
- Tire F/R : Φ 54.8*19.5mm
- Minimum Ground Clearance: 31mm
- Approach Angle: 57°
- Departure Angle: 42 °
- Motor: 180 Brushed motor
- Battery: 2S Lipo 7.4V 380mAh x1
- Remote control distance: 30m
- Approx. operating duration time: 20mins
- Remote control: MG41-BS transmitter, R4A1 receiver with ESC group control board
FMS 1:24 FCX24 Mercedes-Benz Unimog 421 RTR
Description
| Length | 249mm |
| Width | 153mm |
| Height | 160mm |
| Wheelbase | 142mm |
| Tire F/R | Φ 20mm |
| Approach Angle | 49° |
| Departure Angle | 69° |
| Ground Clearance | 40mm |
| Motor | 130 Brushed Motor |
| Remote control distance | 30m |
| Approx. operating duration time | 20mins |
FMS 1:12 TOYOTA FJ45 Pickup Truck RTR
Description
1:12 TOYOTA FJ45 Pickup Truck
To create this officially licensed RC version of the TOYOTA FJ45, FMS super-finely restores the real car, and the degree of restoration is no less than that of the static model.
The hood hinge is the same living hinge as the real car, and it looks slim and beautiful on the 1/12 model car. The motor, steering servo and 2-in-1 integrated ESC / receiver are all hidden under the hood, and the battery is also here, for easy installation. The doors on both sides can be opened, the front windshield can be folded forward, if the roof is removed at the same time, it can be transformed into a convertible shape. If the screws on the slender hinges of the doors are removed, the doors can be removed, showing a more simple and wild performance. At this time, the cockpit is more transparent, the steering linkage action of steering wheel can be seen at a glance, and it is also more convenient to carry 1/12 flexible figures.
The two-speed gearbox provides powerful torque. Metal gears carry power, with bearings all over the whole vehicle, allow it moving forward slowly even if it is fully loaded with gravel. The TOYOTA logo on the rear of the car restores the stereoscopic stamping effect of the steel plate of the real car. The tailgate can be opened to load extra-long "cargo". There are two sets of taillights on the left and right of the tailgate, each set includes a turn signal, a brake light, and a reversing light. With the input of the light control button on the transmitter, the linkage effect is consistent with the driving action. The front headlights have linkage effect of far and near beam and turn signal.
What's in the box:
- 1 x 1:12 TOYOTA FJ45 RTR
- 1 x 2.4G Transmitter
- 1 x 2-in-1 Receiver (installed)
- 1 x 180 Brushed Motor (installed)
- 1 x 9g Plastic Digital Servo (installed)
- 1 x 2S 7.4V 380mAh Battery with PCM
- 1 x USB Charger
- 1 x Hex Wrench Socket
- 1 x Product Manual
Need to Complete:
4 x AAA Batteries for Transmitter
Specification:
- Length: 345mm
- Width: 127mm
- Height: 124mm
- Wheel base: 270mm
- Tire: D:60mm , W:15mm
- Ground clearance: 29mm
- Approach angle: 58°
- Departure angle: 29.9°
- The Highest Driving speed: 8km/h
- Remote control distance: 30m
- Play time: 20 minute
ROCHOBBY RC Rock Crawler RS Red 4WD
Description
1:10 Mashigan - BORN ADVENTURER
For adventurers, the road ahead is always rough and full of thorns, but whether there is a road or no road, this 1:10 Mashigan's 1.9 inch climbing tires can give you confidence, and meanwhile, the four-link suspension system gives you a guarantee of strong power, the metal trapezoidal beams provide you with a solid supportive structure. Even with a hard plastic car shell with a complete interior, Mashigan can easily overcome extreme road conditions. The real first-generation model uses leaf spring suspension, and adventurers will not ignore the history, the chassis can be installed with leaf spring suspension (sold separately) to restore the style of the first generation model. Pursuing the needs of climbing performance and restoration seems to be impossible, but through the compatible design of the chassis and the replacement of a few accessories, it can show a completely different shape. Two postures, and double the fun.
The exquisite interior and four-door full-opening design double the level of detail of this hard-shell RC model, which can be viewed statically or operated indoors. With climbing-level sturdy chassis and suspension system, FMS 1:10 Mashigan make it cool to go wild!
What's in the box:
1 x 1:10 Mashigan RS
1 x 2.4GHz Radio
1 x 2-in-1 Receiver / 40A ESC (installed)
1 x 550 Brushed Motor (installed)
1 x 9g Plastic Digital Servo (installed)
1 x 15kg Metal Digital Servo(installed)
1 x Product Manual
Need to Complete:
- 4 x AA Batteries for Radio
- Battery for Kit (Recommended 2S LIPO 5000mAh XT60 plug)
Specification:
- Radio Control: 160 x 193 x 97mm, 221g (Battery not Included)
- Model Vehicle: 546 x 274 x 282mm, 4kg (Battery not Included)
- Tire: D:115mm, W:30mm
- Wheel Base: 339mm
- Ground Clearance: 82mm
- Approach Angle: 68°
- Departure Angle: 47°
- Driving Speed: up to 15km/h
- Remote Distance: 80m
- Play Time: 20 minute
FMS 1:24 FCX24 Lemur RTR
Description
| Length | 209mm |
| Width | 128mm |
| Height | 120mm |
| Wheelbase | 136mm |
| Tire | D: 66mm, W:22mm |
| Minimum Ground Clearance | 41mm |
| Reduction ratio | (High Gears ) 24.75/(Low Gears ) 99 |
| Motor | 130 Brushed motor |
| Battery | 2S Lipo 7.4V 380mAh x1 |
| Remote control distance | 80m |
| Approx. operating duration time | 20mins |
| Remote control | G3+ R3A transmitter, receiver with ESC group control board |
| Key functions | Two Speed Transmission/Portal Axle |
FMS 1:18 FCX18 Hummer EV Pickup Truck RTR
Description
| Length | 328mm |
| Width | 138mm |
| Height | 133mm |
| Wheelbase | 199mm |
| Tire F/R | Φ 66*22mm |
| Minimum Ground Clearance | 40mm |
| Approach Angle | 51° |
| Departure Angle | 41° |
| Motor | 180 Brushed motor |
| Battery | 2S LiPo 7.4V 900mAh x1 |
| Remote control distance | 30m |
| Approx. operating duration time | 45mins |
| Remote control | MG41-BS transmitter，R4A3 receiver with ESC group control board |
EAZYRC 1:18 Chevrolet Colorado Off-Road Truck RTR Brushless Version
Description
Overview
If you're looking for your first 1:18 RC monster truck, look no further than the EAZYRC 1:18 Chevrolet Colorado, licensed by General Motors LLC. 17g digital servo, 45A brushless ESC, 2S Li-Po battery, and a 4-pole high-torque brushless motor provide sufficient power for the full-time four-wheel drive system. The top speed reaches 45 km/h.
The chassis uses a honeycomb structure with metal reinforcements to increase the overall strength, and the durability is superior to that of similar products. The all-metal gears and metal differentials plus durable steel drive shafts, provide reliable heavy-duty transmission and can withstand extreme high-speed impacts. The whole vehicle adopts a modular chassis design so that the power system, electronic equipment, and differential components are easy to disassemble and the daily vehicle maintenance is simple. The all-metal oil-filled shock absorbers are proven to withstand the impact of high-speed jumps. The tires with asymmetric tread patterns provide EAZYRC 1:18 Chevrolet Colorado with excellent grip, making it easy to run smoothly on almost any road.
What's in Box
1 x 1:18 Chevrolet Colorado RTR
1 x 2.4G Transmitter
1 x R4A Receiver(installed)
1 x 45A Brushless ESC(installed)
1 x 370 Brushless Motor (installed)
1 x 17g Digital Servo (installed)
1X 7.4V 1050mAh LIPO Battery
1 x USB Charger
1 x Hex Wrench Socket
1 x Product Manual
Need to Complete
4 x AA Batteries for Transmitter
Specification
| Length | 310mm |
| Width | 222mm |
| Height | 140mm |
| Wheelbase | 174mm |
| Minimum Ground Clearance | 42mm |
| Motor | 370 brushless motor |
| Battery | 2S Lipo 7.4V 1050mAh |
| Remote control distance | 80m |
| Approx. operating duration time | 10mins |
| Remote control | 2.4GHz |
FMS 1:12 2006 Hummer H1 Alpha RTR
Description
The "Steel Chariot" of a Passionate and Tough Warrior
The FMS HUMMER H1 is coming strong! Unlike the common scale crawlers on the market, FMS HUMMER H1 is a very high-detail RC crawler that comes complete with a full scale chassis structure and drivetrain system, and an exquisite scale interior with full door function.
Power comes from a 370 motor. Two servos respectively control both the switch between high and low speed gears and the operation of the transfer case, thus switching between rear drive and four-wheel drive. Both the front and rear differentials also have a differential lock function, each driven by a servo which can be locked by remote control. Four metal drive shafts transmit power from the differential to the reduction gear assembly, commonly known as a "portal axle". The HUMMER H1 also has a full metal gear-set and 47 ball-bearings. We have included the rear wheel steering as an additional hidden function, so you now have a total of 4 steering modes! The extra mode, which can reduce the steering radius by 50%, is ideal in confined spaces.
The HUMMER H1 uses a front mid-engine layout just like the real vehicle, and the hood is designed to be flipped forward. Four doors can all be opened, and the smart door lock mechanism is a separate unit. The cabin also features a highly detailed dashboard and moving steering wheel that turns with the main steering. The roof is removable and the windshield can be lowered forward. The body of the Hummer is mainly made of aluminum alloy and fiberglass, and the fixing method is riveting. A 2.4G 7CH digital proportional radio system, a receiver/ ESC/ light control three-in-one unit, 7 servos（including 13g metal gear servo x 2pcs)
The FMS HUMMER H1 is presented as it should be – a no compromise “work of art” scale vehicle that is sure to be one for collectors and enthusiasts alike!
What's in Box
1 x 1:12 HUMMER H1 RS
1 x 2.4GHz Transmitter
1 x 2-in-1 Receiver / 40A ESC (installed)
1 x 370 Brushed Motor (installed)
5 x 9g Plastic Digital Servo (installed)
2 x 13g Metal Digital Servo(installed)
1 x Hex Wrench Socket
1 x Product Manual
Need to Complete
4 x AAA Batteries for Transmitter
Battery for Kit (Recommended 2S 7.4V 2000mAh 20C XT30 plug; Battery compartment size: L 90mm x W 35mm x H 20mm)
Specification
Length: 408mm
Width: 222mm
Height: 162mm
Wheelbase: 272mm
Tire F/R: Φ 78 × 25mm
Approach Angle: 52°
Departure Angle: 39°
Speed: the highest fast gear is 8km/h, the highest slow gear is 5km/h
Minimum Ground Clearance: 40mm
Motor: 370 Brushed motor
Remote control distance: 30m
Approx. operating duration time: 20mins
Remote control: G7 + R7A Transmitter receiver set
RC Airplane Transmitter & Receiver Set (6 channel)
Description
For 1220mm Ranger, 1300mm PA-18, 1280mm Easy Trainer, 800mm F4U, 1220mm Super EZ, 800mm P‑51D, 1020mm F3A, 1400mm J-3, 1400mm Kingfisher, 64mm F-18 V2, 64mm F-35 V2, 64mm F-15 V2, 800mm F4U V2, 800mm Zero V2, 800mm T-28, 750mm Edge 540, 1020mm F3A, 1400mm F3A, 1400mm Pitts V2, 1500mm Moa, 800mm Easy Trainer, 1500mm Maule, 1700mm PA-18, 64mm Rafale, 3000mm Fox, 2300mm FOX, 1500mm Cessna, 2500mm ASW-17, 64mm Futura, 1800mm Ranger
